The Collier Report of U.S. Government Contracting

Sampling of Federal Government Funding Actions/Set Asides

In order by amount of set aside monies.

• $100 - Wednesday the 14th of March 2012
  Federal Acquisition Service
  GSA/FAS TOOLS ACQUISITION DIVISION II
  DRILL, MASONRY, POWER HAMMER: IAW ANSI (ANSI) B2 12.15-1994 CUTTING TOOLS - CARBIDE-TIPPED MASONR Y DRILLS AND BLANKS FOR CARBIDE-TIPPED MASONRY D RILLS. TYPE: DRILL, MASONARY, POWER HAMMER MATER IAL: STEEL OVERALL FMD 16 CUTTING STYLE: SLOW HE LIX EXCEPTION TO STANDARD: OVERALL LENGTH: 18 IN CH MIN. (PARTIAL DESCRIPTION) EXPEDITE

  ---

• $100 - Tuesday the 6th of December 2011
  Federal Acquisition Service
  GSA/FAS TOOLS ACQUISITION DIVISION II
  PLEASE SEE IPD OR LONG DESCRIPTION FOR FURTHER D ETAILS. PRODUCT MADE IN CHINA

  ---

• $987 - Thursday the 28th of June 2012
  Federal Acquisition Service
  GSA/FAS TOOLS ACQUISITION DIVISION II
  LEVEL, CYLINDRICAL, CIRCULAR VIAL: SPECIAL FEATU RES: COMPONENT OF M2 INFANTRY AND M3 CALVARY FIG HTING VEHICLES. IAW U.S. ARMY TANK-AUTOMOTIVE CO MMAND DRAWING 12297933, REVISION B, DATED SEPTEM BER 12, 1997. (EXCEPTIONS APPLY) (PARTIAL DESCRI PTION)

  ---

• $9,842 - Tuesday the 10th of July 2012
  Defense Logistics Agency
  DLA TROOP SUPPORT
  4520809110!BOA

  ---

• $979 - Tuesday the 5th of June 2012
  Federal Acquisition Service
  GSA/FAS/APPLIANCES ACQUISITION DIVISION I
  WRENCH PIPE (STRAP); MSP; 413

  ---

• $98 - Thursday the 20th of October 2011
  Federal Acquisition Service
  GSA/FAS TOOLS ACQUISITION DIVISION II
  TAPE, MEASURING: TANK GAGING TAPE TAPE LENGTH: 1 00 FEET TAPE WIDTH: 0.5 INCH TAPE THICKNESS: 0.0 12 INCH GRADUATIONS: 1/8THS OF INCH MATERIAL: ST EEL FINISH: NICKEL/CHROME PLATED FEATURES: RIGHT TO LEFT READING, BLACK MARKINGS ON ONE SIDE ONL Y, SNAP-SWIVEL HOOK ON FRONT END FOR ATTACHMENT OF PLUMB BOB (NOT INCLUDED), WINDING HANDLE FOLD S FOR STORAGE AND TO LOCK TAPE AT ANY EXTENDED P OSITION. (PARTIAL DESCRIPTION)

  ---

• $97 - Thursday the 5th of April 2012
  Federal Acquisition Service
  GSA/FAS TOOLS ACQUISITION DIVISION II
  PUNCH, CUTTING, DOUBLE BOW: IAW FEDERAL SPECIFICATION GGG-P-833B, DATEDJUNE 20, 1994. TYPE I: CUTTING (DRIVE) CLASS B:CIRCULAR STYLE 1: DOUBLE BOW MATERIAL: CARBON STEEL SZ: 11/16 INCH SPECIAL FEATURES: ARCH PUNCHHAS THE INSIDE TAPER WHICH PERMITS THE PUNCHINGS TO CLEAR EASILY THROUGH THE BARREL. PUNCHES HAVE FULLY POLISHED BARRELAND BLACK ENAMEL HANDLE. THE CUTTING EDGE IS FULLY TEMPERED ALL THE WAYTHROUGH AND PROPERLY FINISHED TO PROVIDE LONG USE TROUBLE FREE PUNCHING. (PARTIAL DESCRIPTION)

  ---

• $97 - Monday the 4th of June 2012
  Federal Acquisition Service
  GSA/FAS TOOLS ACQUISITION DIVISION II
  PUNCH, CUTTING, DOUBLE BOW: IAW FEDERAL SPECIFICATION GGG-P-833B, DATEDJUNE 20, 1994. TYPE I: CUTTING (DRIVE) CLASS B:CIRCULAR STYLE 1: DOUBLE BOW MATERIAL: CARBON STEEL SZ: 11/16 INCH SPECIAL FEATURES: ARCH PUNCHHAS THE INSIDE TAPER WHICH PERMITS THE PUNCHINGS TO CLEAR EASILY THROUGH THE BARREL. PUNCHES HAVE FULLY POLISHED BARRELAND BLACK ENAMEL HANDLE. THE CUTTING EDGE IS FULLY TEMPERED ALL THE WAYTHROUGH AND PROPERLY FINISHED TO PROVIDE LONG USE TROUBLE FREE PUNCHING. (PARTIAL DESCRIPTION)

  ---

• $97 - Wednesday the 19th of October 2011
  Federal Acquisition Service
  GSA/FAS TOOLS ACQUISITION DIVISION II
  DRILL, TWIST: IAW NATIONAL AEROSPACE STANDARD NA S 907, DRILLS, HIGH SPEED STEEL (&COBALT) 1/16 INCH THRU 1.00 INCH, REVISION 11, LIST OF CURREN T SHEETS, DATED 10 FEBRUARY 2006. TYPE: J (STRAI GHT ROUND SHANK - JOBBERS LENGTH), GENERAL PURPO SE CUTTING DIAMETER: WIRE GAGE SZ 20 MATERIAL: C OBALT HSS FLUTE LENGTH: 2-1/8 INCHES OVERALL LEN GTH: 3-1/4 INCHES POINT ANGLE: 135 DEGREES POINT TYPE: SPLIT CUTTIING DIRECTION: RIGHT-HAND FLUT E QUANTITY: 2. (PARTIAL DESCRIPTION) EXPEDITE

  ---

• $97 - Thursday the 6th of October 2011
  Federal Acquisition Service
  GSA/FAS TOOLS ACQUISITION DIVISION II
  TAP, THREAD CUTTING: IAW AMERICAN SOCIETY OF MEC HANICAL ENGINEER (ASME) B94.9-1999 TYPE: STANDAR D STRAIGHT THREAD THREAD SZ-SERIES: 3/8-24 UNF P ITCH DIAMETER LIMITS: (H3), 0.3489/ 0.3494 INCH CHAMFER TYPE: TAPER THREAD FORMING METHOD: GROUN D STYLE DESIGNATOR: STRAIGHT FLUTE THREAD DIRECT ION: RIGHT-HAND FLUTE QUANTITY: 4 MATERIAL: HIGH SPEED STEEL (PARTIAL DESCRIPTION)

  ---